What did you do to your FZ today? - Page 20

def · 11-20-2009, 08:02 PM

gutted the cat and replaced brocken bits from last weekends smack down

fjurado · 11-20-2009, 08:24 PM

Here is my gal.................................

AleHole · 11-20-2009, 10:06 PM

Finally installed the shorter dogbones I bought off the classifieds a few months back. What a difference that made for turn in. However, it affected the tire clearance while on the center stand so its a bit tougher to spin 180 now.

sanaga · 11-22-2009, 10:01 AM

clean it and ride it for 200km ....very nice bike

duts87ss · 11-22-2009, 11:32 AM

Finished the install of my Clear Alternatives tail light. Also re-installed the bar-end mirrors to take it to work tomorrow (took them off for my first track day last weekend).

wot-75 · 11-23-2009, 07:28 AM

mmm.. tasty bits going on the front rim tonight.

EBC XC rotors for the rim and EBC Extreme Pro pads for the calipers!

theWolfTamer · 12-02-2009, 01:54 PM

I finally got to change the oil. It wasn't overdue but it did need doing.

abe57 · 12-02-2009, 03:38 PM

Sadly put her up for the winter.....

hotboot · 12-02-2009, 03:57 PM

Installed R6 pegs and newly rebuilt Traxxion forks. Ice and snow in Dallas for the next few days.....just my luck can't ride the scoot.

82packer · 12-02-2009, 06:19 PM

Just got home from work 42 degrees and windy. Snow next 3 days and cold next 10 days on long range forcast. SO she is getting parked for a bit. Been a great riding season.

Bird Man · 12-12-2009, 02:59 AM

Fitted Pazzo shorties,Warp Speed rad protector and Zap Racing fender eliminator

Hairball · 12-13-2009, 12:20 PM

I put stabilizer in the tank, pulled the battery and put the battery tender on it. Pushed her in the back corner of the garage and covered her up for the long winter nap.

Come on spring!!!!!!!!!!!!!!!!!!

V10KLZZ71S · 12-13-2009, 01:07 PM

Put pictures of my bike nude on the internet.

miles2912 · 12-13-2009, 04:16 PM

Rain finally let up and it was a gorgeous sunny day, Went for a nice ride to a buddys house to watch the Vikings win over the Bengals.

slow0ne · 12-13-2009, 10:05 PM

Went for a short ride today to get the fluids moveing after sitting for about 10 days due to weather. Short ride because it was still only 37 degrees out but i wanted to see if it was ok after -15 degree low on wensday. I was a little worried because i have a 30% antifreeze mix in to help the water wetter work better. My garrage is about 15 degrees or so warmer than out side but the pepsi and mountain dew in the garrage froze solid. The fz ran fine so back on the battery tender. I'am hopeing to go for a longer ride this wensday because it's supposed to hit 50 degrees.

whittlebeast · 12-14-2009, 04:31 AM

The Power Commander LCD dash shows up today. Not sure if I will be able to get it installed in time to beat the weather. High today 50, low tonight will be in the teens. I am looking forward to the switchable maps on the fly.

AW

t84a · 12-14-2009, 04:42 AM

Installed the SW-Motech hard bag mounts (side and rear). I had to modify two of the brackets since I no longer have signal lights and needed to modify the license plate holder. I just need to paint them today and put them on. The Givi bags are supposed to show up today. Then I need to decide whether or not to paint the tops to match my bike.

Dr. Wood · 12-19-2009, 12:57 PM

Just about to go set the open close points for the PCIII I just installed.

So far this series of mod has been quite impressive on the butt dyno.

Later that day:

Man that was too easy. I printed out the two page instructions from Ivans thread and thought, "this might suck". But it went smooth as butter. Done in 5 min.

jwhelan65 · 12-19-2009, 03:02 PM

Just rode the snot out of it today.....thats all

...67 and sunny here in San Antone!!!!!

Cruzman · 12-21-2009, 09:18 PM

Finally got around to upgrading the accessory wiring. I now have all my accessories on a relay and power distribution point. As well as a integrated 12 volt power port. I still have some major cleaning to do on the bike. I recently went out for a 5 hour ride in fog and rain and it has been so cold here that I have only hosed it off.

I am still trying to decide If I want to put some non conductive material over the top of the power distribution blocks and I am pretty sure I will be putting heat shrink on the connectors that hook to the relay.

Picture of my install:
http://picasaweb.google.com/cruzman2...eat=directlink

11-22-2009, 11:32 AM	#385
duts87ss I ride slow. Join Date: Aug 2007 Location: Ocean Springs, MS USA Posts: 178	Finished the install of my Clear Alternatives tail light. Also re-installed the bar-end mirrors to take it to work tomorrow (took them off for my first track day last weekend). __________________ ============ Dustin '07 Raven - \|'N Conversion\|BMC\|AB Mod\|Graves Stacks\|Ivan's Flies\|Harness relocated\|FCE\|PCIII&IM\|Full Yosh TRC\|AIS removed\|Graves servo Eliminator\|'04 R1 Forks w/ Traxxion AK-20\|Penske 8983\|Spiegler Brake Lines\|Gilles Rearsets\|16/46 520 Conversion\|

12-02-2009, 01:54 PM	#387
theWolfTamer Lupie on a Mission Join Date: Oct 2007 Location: Firmly Planted in the Georgia Red Clay, U.S.A Posts: 1,262	I finally got to change the oil. It wasn't overdue but it did need doing. __________________ 2005 FZ1: RR Carb Stuff ▪ GPR Speed Cone Muffler ▪ ZG Sport Touring Screen ▪ devilsyam black frame plugs ▪ billet pegs ▪ T-Rex Sliders ▪ Seat Mounted Top Case ▪ Adjustable Levers ▪ Pro Grips Gel 725 EVO ▪ Bi Xenon HIDs ▪ Aux Lights ▪ LED Signals ▪ Pod Lights ▪ rad guard ▪ gen2 handlebar ▪ R1 Shift Arm ▪ Multiguage ▪ Throttlemeister ▪ R6 Shock ▪ R1 Forks theWolfTamer Chronicles

12-02-2009, 03:38 PM	#388
abe57 "King-of-Bee's" Join Date: Jul 2003 Location: Columbus,IN Posts: 3,969	Sadly put her up for the winter..... __________________ George Maybe So,What do You Think?

12-02-2009, 03:57 PM	#389
hotboot pony boy carry me home Join Date: Jan 2004 Location: D/FW Posts: 8,890	Installed R6 pegs and newly rebuilt Traxxion forks. Ice and snow in Dallas for the next few days.....just my luck can't ride the scoot. __________________ It's all about the good life and staying easy with the world - Lyle Lovett

12-13-2009, 12:20 PM	#392
Hairball Dazed and confuzed Join Date: Aug 2003 Location: Cedarburg,WI Posts: 466	I put stabilizer in the tank, pulled the battery and put the battery tender on it. Pushed her in the back corner of the garage and covered her up for the long winter nap. Come on spring!!!!!!!!!!!!!!!!!! __________________ R-77 Carbon,PC111,Ign module,no flys,BMC filter,Air Box mod, FCE, Factory Pro Velocity Stacks,Roth AIS plates, Mag-Knight Carbon Tank Bra, Clearalternatives taillight, Hyperpro RSC stabilizer,Penski Double Adjustable,07 R1 Forks with AK-20 carts, Rizoma Rearsets,Stealth Rear Sprocket, Spiegler SS brake lines, SW-Motech Crashbars,Sargent Seat,Rizoma conical bars and 42mm risers, Rizoma Reverse Retro Mirrors, speedohealer,16 tooth c/s, jwhelan's radiator guard

11-20-2009, 08:02 PM	#381
def Registered User Join Date: Jun 2009 Posts: 4	gutted the cat and replaced brocken bits from last weekends smack down

11-20-2009, 10:06 PM	#383
AleHole Registered User Join Date: Jan 2009 Location: Seattle Posts: 1,271	Finally installed the shorter dogbones I bought off the classifieds a few months back. What a difference that made for turn in. However, it affected the tire clearance while on the center stand so its a bit tougher to spin 180 now.

11-22-2009, 10:01 AM	#384
sanaga power wheelie junkie Join Date: Jul 2007 Location: indonesia Posts: 33	clean it and ride it for 200km ....very nice bike

12-02-2009, 06:19 PM	#390
82packer Registered User Join Date: Nov 2008 Location: Base of the Pinkie Posts: 1,415	Just got home from work 42 degrees and windy. Snow next 3 days and cold next 10 days on long range forcast. SO she is getting parked for a bit. Been a great riding season.

12-12-2009, 02:59 AM	#391
Bird Man Aussie Join Date: Jun 2009 Location: Western Australia Posts: 13	Fitted Pazzo shorties,Warp Speed rad protector and Zap Racing fender eliminator

12-13-2009, 01:07 PM	#393
V10KLZZ71S I am the 53% Join Date: Aug 2006 Location: Gretna,Louisiana/Tennessee Colony, Texas Posts: 4,924	Put pictures of my bike nude on the internet. __________________ 06 SILVER FZ1 Graves FE ,Holeshot header w/Telco Slip On, FCE,Ivans flies, Graves V- Stacks,Graves flush mounts, PCIII w/Ivans map,Ign module,AIS eliminator, BMC Air Filter, Lars' Airbox mod. 15T Frt Sprocket, Rizoma grips,Pazzo, Graves sliders,C-dog screen.Graves exup plug, EBC HH pads, Carrozzeria V-stars, Galfer rotors,Fren Tubo brk lines,Traxxion AK-20, Penske shock 07 MV Agusta Brutale' 910R Ferracci chip, PCIII, Arrow Thunder

12-13-2009, 04:16 PM	#394
miles2912 Smiling politely Join Date: Aug 2009 Location: Long Beach - CA Posts: 731	Rain finally let up and it was a gorgeous sunny day, Went for a nice ride to a buddys house to watch the Vikings win over the Bengals. __________________ 2009 Yamaha FZ1 \| MIVV CF GP Slip on \| 16t sprocket \| SpeedoDRD \| Cat Gutted \| AIS Plugged \| Cheap Shorty Levers

12-13-2009, 10:05 PM	#395
slow0ne Registered User Join Date: Jun 2008 Location: Colorado Springs Colo. Posts: 184	Went for a short ride today to get the fluids moveing after sitting for about 10 days due to weather. Short ride because it was still only 37 degrees out but i wanted to see if it was ok after -15 degree low on wensday. I was a little worried because i have a 30% antifreeze mix in to help the water wetter work better. My garrage is about 15 degrees or so warmer than out side but the pepsi and mountain dew in the garrage froze solid. The fz ran fine so back on the battery tender. I'am hopeing to go for a longer ride this wensday because it's supposed to hit 50 degrees. __________________ blue 07, 2bro slipon w/p1-r, holeshot header, k&n, air box mod, flys tied, pc3, 16t, cheap ais, washer mod, home made fender elimenator, narrowed handle bars, front led flushmounts,speed drd.

12-14-2009, 04:31 AM	#396
whittlebeast Registered User Join Date: Jul 2009 Posts: 1,506	The Power Commander LCD dash shows up today. Not sure if I will be able to get it installed in time to beat the weather. High today 50, low tonight will be in the teens. I am looking forward to the switchable maps on the fly. AW __________________ Max acceleration is always with the front tire slightly in the air. When the racers get done doing the impossible, the engineers get a chance to rebuild the model. Holeshot Highmount quiet, No-Mar Fender Eliminator, SW-MOTECH Bar risers and Crashbars with Saten666 highway pegs, HEL Stainless brake lines, PC5 with full time widebands and data logging running a MAP based custom map tuned with MegaLogViewer HD, T-Rex Frame sliders, 16 - 45 gears, Throttlemeister.

12-14-2009, 04:42 AM	#397
t84a Real Bikers Pedal Join Date: Nov 2008 Location: Maryland Posts: 2,396	Installed the SW-Motech hard bag mounts (side and rear). I had to modify two of the brackets since I no longer have signal lights and needed to modify the license plate holder. I just need to paint them today and put them on. The Givi bags are supposed to show up today. Then I need to decide whether or not to paint the tops to match my bike. __________________ Ken in Maryland 10 Raider 08 FZ1 Yosh R77 Titanium slip on, Graves AIS block off plates, EXUP Eliminator, LARs airbox mod, K&N filter, Ivan's sub-throttle plates, Ivan's FCE, PCV, SpeedoDRD, Ivan's PCV map (awesome!), Satan666 R1 shock adapter w/R1 shock, Satan666 pegs (also awesome), dirt road seats, K1000 mirrors. JOIN THE AMA Helmet Fact

12-19-2009, 12:57 PM	#398
Dr. Wood Fontana's 1st crash test dummy Join Date: Sep 2006 Location: So. Cal. (Fontana) Posts: 1,103	Just about to go set the open close points for the PCIII I just installed. So far this series of mod has been quite impressive on the butt dyno. Later that day: Man that was too easy. I printed out the two page instructions from Ivans thread and thought, "this might suck". But it went smooth as butter. Done in 5 min. __________________ Mod list: PCIII, perfection map, Flies, FCE, o2 discon, BMC filter Gutted cat's, Mivv GP Ti, AIS, Airbox mod, Speed King Rear sets, Unprofessionally butt dyno'ed, results..... Last edited by Dr. Wood; 12-19-2009 at 08:03 PM. Reason: update

12-19-2009, 03:02 PM	#399
jwhelan65 Registered User Join Date: Jun 2008 Location: Dallas / Ft worth Posts: 782	Just rode the snot out of it today.....thats all ...67 and sunny here in San Antone!!!!! __________________ 08 Granite Gray - Yoshi R-77 Full exhaust - PCIII - Lars airbox mod - BMC filter - 520 DID Gold -45t Supersprox - Renthal 16t - Pilot Road 2CT's - Graves R1 fender eliminator - Yamaha Gel seat - Watsen flushmounts - CD speedscreen - Rad-Armor guard. - Evotech hanger.

12-21-2009, 09:18 PM	#400
Cruzman Registered User Join Date: Sep 2009 Location: Hiram, GA Posts: 1,587	Finally got around to upgrading the accessory wiring. I now have all my accessories on a relay and power distribution point. As well as a integrated 12 volt power port. I still have some major cleaning to do on the bike. I recently went out for a 5 hour ride in fog and rain and it has been so cold here that I have only hosed it off. I am still trying to decide If I want to put some non conductive material over the top of the power distribution blocks and I am pretty sure I will be putting heat shrink on the connectors that hook to the relay. Picture of my install: http://picasaweb.google.com/cruzman2...eat=directlink __________________ Cruzman Atlanta, GA Past 1981 Suzuki GS 750-EZ 1985 FJ1100 "Trigger" (Stock) Present 2002 FZ1000 "Stella" (slipon, Re-jeted, AIS eliminated, fender eliminator, mini led turn signals, K&N filter, R6 rear shock conversion,Gauge of Eternal Coolness, 4 degree advancer mod (New) SS Brake-Lines (Stupid Stuff) Emergency Room $500 ,MRI and Arthrogram $430, Misc Dr visits $100. Physical Therapy $ 345 (Grand Total $1375 out of pocket)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

wArDoG (Prez, Treasurer, Web Site & Admin)	Rabeet (Admin)
firstfz (Web Site & Admin)	Desmo (Admin)
RoadRashed (Admin)	dipps (Admin)
Black Mantis (Moderator)	pogden (Moderator)